IES Virtual Engineering Laboratories / UTM V2.1

UTM lecturer guide & worked calculations

Model utm-v2.1. All materials are illustrative, not measured or certified properties. Use this formative laboratory alongside supervised physical work; it does not certify practical competence.

01. Determining tensile modulus

Objective
Determine E from two readings within the linear elastic region.
Theory
The elastic slope is E = (σ₂ − σ₁) / (ε₂ − ε₁). Strain is dimensionless; MPa / 1000 gives GPa.
Preparation
Choose steel, rectangular 10 × 5 mm, L₀ = 50 mm. Attach the ideal extensometer. Use the graph Elastic region control and pause early.
Prediction
Which material do you expect to have the steepest elastic gradient?
Measurements
Select two elastic data points. Record force, extension, stress and dimensionless strain for each.
Calculation task
Calculate area, both stresses and strains, then the slope in GPa. Avoid using plastic-region points.
Interpretation
How would a crosshead measurement differ from gauge strain on a real machine?
Worked calculation
For A₀ = 50 mm² and L₀ = 50 mm: at ε = 0.0005, σ = 100 MPa, F = 5000 N, ΔL = 0.025 mm. At ε = 0.001, σ = 200 MPa, F = 10000 N, ΔL = 0.050 mm. E = 100 / 0.0005 = 200000 MPa = 200 GPa.
Lecturer notes
Check that the learner uses dimensionless strain rather than percent. In real testing, machine and grip compliance make crosshead extension unsuitable for accurate modulus without correction. The simulator uses ideal gauge data.

02. Comparing steel and aluminium

Objective
Compare stiffness, peak strength and ductility while controlling geometry.
Theory
Stiffness, strength and ductility describe different properties. The same stress requires the same force when original area is unchanged.
Preparation
Run steel and aluminium with identical area, gauge length and speed. Add each completed test to the comparison laboratory.
Prediction
Which will extend further under the same load in the elastic region?
Measurements
Record elastic slope, maximum force, UTS and model elongation at fracture for each.
Calculation task
For σ = 100 MPa, use ε = σ/E and ΔL = εL₀ to compare extensions.
Interpretation
Explain why stiffness alone does not rank fracture strain or ultimate strength.
Worked calculation
At 100 MPa and L₀ = 50 mm: steel ε = 100/200000 = 0.0005, ΔL = 0.025 mm. Aluminium ε = 100/69000 ≈ 0.001449, ΔL ≈ 0.07246 mm. These are assumed educational profiles, not all steels and alloys.
Lecturer notes
Keep area fixed for force comparisons. The alloy preset is deliberately generic; do not extrapolate its values to a real material designation.

03. Identifying yield and ultimate tensile strength

Objective
Identify first yield, an offset proof stress, UTS and fracture load.
Theory
First yield marks departure from elastic response in a model with a yield plateau. Rp0.2 is the intersection of σ = E(ε − 0.002) with the curve. UTS is the maximum engineering stress.
Preparation
Complete steel, then aluminium. Inspect the labelled curve events. Use the point selector to record measurements.
Prediction
Will fracture occur at the maximum force?
Measurements
Record yield/proof stress, peak stress and force immediately before fracture. Distinguish the last pre-break load from zero post-break load.
Calculation task
Calculate steel UTS from the maximum force and original area.
Interpretation
Why can engineering stress fall while the specimen continues extending?
Worked calculation
Steel: Fmax = 21500 N for A₀ = 50 mm²; UTS = 21500/50 = 430 MPa. First yield = 250 MPa; pre-break stress = 330 MPa and force = 16500 N. Aluminium Rp0.2 ≈ 208.861 MPa for the curved V2.1 hardening law, from the numerical offset-line intersection. Historical V2.0 records retain their original 202.914 MPa value.
Lecturer notes
The model represents nominal necking by a falling engineering-stress branch. It does not calculate local true stress or post-necking transverse area.

04. Comparing ductile and brittle behaviour

Objective
Use curve shape, elongation and external work to distinguish brittle and ductile response.
Theory
Brittle profiles fracture without a plastic branch. Ductile profiles can yield, soften, draw and harden. External work is ∫F d(ΔL), with N mm converted to J.
Preparation
Compare brittle polymer and ductile thermoplastic using polymer dog-bones, equal reduced-section area and equal gauge length.
Prediction
Which curve will enclose the greater area?
Measurements
Record fracture strain, peak stress and work. Observe whether a yield event exists.
Calculation task
For a linear-elastic brittle specimen, work = ½ Ffracture ΔLfracture / 1000.
Interpretation
Why is work geometry-dependent and unsuitable as an intrinsic fracture toughness value?
Worked calculation
Brittle preset, A₀ = 50 mm² and L₀ = 50 mm: σf = 60 MPa, Ff = 3000 N, εf = 0.02, ΔLf = 1 mm, work = 1.5 J. A brittle specimen can be stiff without being ductile.
Lecturer notes
The thermoplastic curve is rate-independent. Do not claim speed or temperature predictions. Neck appearance is a qualitative strain-driven indicator.

05. Investigating specimen geometry and force–extension behaviour

Objective
Explain how cross-section and gauge length affect machine readings without changing an assumed material law.
Theory
F = σA₀ and ΔL = εL₀. Rectangular/dog-bone reduced section: A₀ = wt. Cylinder: A₀ = πd²/4.
Preparation
Test the same material at 10 × 5 mm and 5 × 5 mm. Then repeat with a cylindrical specimen. Keep material and physical speed recorded.
Prediction
What happens to force when area halves? What happens to extension when gauge length doubles?
Measurements
Overlay both graph types and record force at a common engineering strain.
Calculation task
At 200 MPa, compare force for A₀ = 50 mm² and 25 mm². Find the diameter giving A₀ = 50 mm².
Interpretation
Why do stress–strain overlays coincide while force–extension curves differ? Does test speed change strength in this model?
Worked calculation
At 200 MPa, 50 mm² requires 10000 N and 25 mm² requires 5000 N. For 50 mm², d = √(200/π) ≈ 7.979 mm. Doubling L₀ doubles extension at the same strain. At fixed mm/min it also halves nominal strain rate, but the model has no rate-sensitive strength.
Lecturer notes
Dog-bones use their actual reduced-section width and thickness. Shoulders are treated as rigid, so crosshead displacement equals gauge extension. This is not a finite-element geometry analysis.

Formative questions and answers

  1. How does the initial gradient relate to elastic modulus?

    E is the slope of engineering stress against dimensionless strain in the elastic region.

  2. Why is engineering stress based on the original area?

    Original area supplies a consistent nominal reference; true stress is not modelled.

  3. Which material has the greatest elastic stiffness?

    The low-carbon steel preset has the highest assumed elastic modulus.

  4. What happens to engineering stress after the ultimate strength?

    For the ductile presets it falls in the nominal necking branch; brittle profiles fracture at their peak.

  5. Which specimen property changes force without changing the stress–strain curve?

    Original cross-sectional area changes force through F = σA₀.

Review evidence

Check units and control of variables, distinction between assumed parameters and calculated results, use of original area and gauge length, and whether the learner distinguishes observed partial results from a completed fracture test. Compare work only when specimen geometry is controlled.

Return to the laboratory · Technical notes